En ole vaihtanut (eli tämä on sitä lunttausta..), googlehaulla löytyi tämä: https://www.lxforums.com/board/awd/134156-transfer-front-differential-fluid.html Couple of other things to remember... When changing the diff fluids ALWAYS remove the fill plug before the drain plug. Simply, if for some reason the fill plug is seized in place and won't come out you're not sitting there with an empty diff and no way to fill it. the rear diff will require a 14mm hex head socket. That's not in most sets, so make sure you have one. The transfer case has a fill plug, a drain plug, and an inspection plug. Remove all three. When filling replace the drain plug, then fill from the top fill plug hole until the fluid begins to run our of the inspection plug hole. Let it drain for a bit until it stops, then replace the fill and inspection plugs. You don't need to remove the front and rear prop shafts to do this. You will need to remove the brace and the damper, which is just a heavy hunk of metal. the top fill hole is a little bit hard to get to, but you can get there. Make sure to clean the threads of all plugs before putting them back in. I even wrapped some teflon tape on the threads so that they will be a lot easier to remove next time the unit(s) have to be serviced. Use a fluid pump to get the T-Case and diff fluids up into the units. I used a manual pump like this: It does take a little bit of time, and there is some effort, especially with the T-Case, but it's not too bad. SPECIFICATIONS - FLUID CAPACITIES DESCRIPTION SPECIFICATION Fuel Tank - V6 Engine 68 L (18 gal.) Fuel Tank - V8 Engine 72 L (19 gal.) Engine Oil* - 2.7 L 5.7L (6.0 qts.) Engine Oil* - 3.5 L 5.7L (6.0 qts.) Engine Oil* - 5.7 L 6.6 L (7.0 qts.) Engine Oil* - 3.0 L Diesel 8.5 L (9.0 qts.) Engine Oil* - 6.1 L 6.6 L (7.0 qts.) Cooling System - 2.7 L** 9.2 L (9.7 qts.) Cooling System - 3.5 L** 10.0 L (10.6 qts.) Cooling System - 5.7 L** 13.8 L (14.6 qts.) Cooling System - 6.1 L** 14.0 L (14.8 qts.) Cooling System - 3.0 L Diesel** 13.2 L (14.0 qts.) *(includes filter) *(includes heater and coolant recovery bottle filled to MAX level) AUTOMATIC TRANSMISSION Service Fill - NAG1 5.0 L (10.6 pts.) Overhaul Fill - NAG1 7.7 L (16.3 pts.)♦ Service Fill - 42RLE 3.8L (4.0 qts) Overhaul Fill - 42RLE 8.3L (17.6 pts)♦ ♦Dry fill capacity. Depending on type and size of internal cooler, length and inside diameter of cooler lines, or use of an auxiliary cooler, these figures may vary. TRANSFER CASE MS140 0.6L (1.3 pts.) AXLE - FRONT 175MM FIA Axle 600 ml (0.63 qts) AXLE - REAR 198 MM RII Axle 1.4L (1.5 qts.) 210 MM RII Axle 1.6L (1.7 qts.) 215 MM RII Axle 1.6L (1.7 qts.) RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS CHASSIS Component Fluids, Lubricants and Genuine Parts Automatic Transmission Mopar � ATF+4 Automatic Transmission Fluid or equivalent. Brake Master Cylinder Mopa � DOT 3 and SAE J1703 or equivalent should be used. Use only recommended brake fluids. Front Axle API Certified GL-5 SAE 75W90 Synthetic Gear Lubricant or equivalent. Power Steering Reservoir Mopar � Power Steering Fluid + 4, Mopar � ATF+4 Automatic Transmission Fluid or equivalent. Rear Axle API Certified GL-5 SAE 75W140 Synthetic Gear Lubricant or equivalent. Transfer Case Mopar � Transfer Case Lubricant LX, P/N 05170055EA, or equivalent.